Scantool Ready-or-Not Bedienungsanleitung PDF herunterladen

1. Install OBDwiz software 2. Locate the diagnostic connector.

Insert the software CD in your CD-ROM drive.

The scan tool selection menu will automatically

appear. Click on the icon labeled Ready-or-Not:

5. Launch OBDwiz software

To launch the software, click on Start

Programs . Click the Auto

Detect button, then click the Connect button.

6. Technical support

Should you run into problems, technical support

is just a click away:

3. Connect Ready-or-Not (RoN) to

the DLC

Follow connection diagram (directly below) to

connect RoN to the diagnostic connector using

The Ready-or-Not menu will appear. Click on

the black OBD-II cable (steps & ).

OBDwiz and follow the prompts to install the

software:

4. Connect scan tool to the PC

Connect RoN to your PC's serial port using the

gray serial cable (steps & ). Turn the vehicle’s

ignition to the Key On, Engine Off position.

Note that some laptops do not have a built-in

serial port. Inexpensive USB to Serial converters

are available from the ScanTool.net website, or

your local computer store.

If the menu does not appear, click Start Run,

type D:\setup.exe (where ‘D’ is the drive letter of

your CD-ROM drive), and click OK.

Watch the LEDs as you are performing step .

The six monitor LED’s will momentary light up

green then red, followed by a “beep” sound.

The 16-pin D-shaped diagnostic link connector

(DLC) should be located in the passenger or

gOBDwizgOBDwiz

driver's compartment in the area bounded by the

driver's end of the instrument panel to 300 mm

(~1 ft) beyond the vehicle centerline, attached to

the instrument panel and easy to access from the

driver's seat. The preferred location is between

the steering column and the vehicle centerline.

— Knowledgebase - contains answers to

the most commonly asked questions,

general information about OBD-II, and

troubleshooting information.

— Forum - allows you to share information

and get support from other ElmScan 5

users.

All of the above resources can be accessed from

our website:

A B

C D

www.ScanTool.net.

vehicle

OBD-II cable

serial cable

C D

Ready-or-Not

CAT

EVAP

SEC. AIR

O HTR

EGR

READY NOT READY

RoN

computer

1 2

Ready-or-Not 1
READY NOT READY 2

Inhaltsverzeichnis

Seite 1 - Ready-or-Not

1. Install OBDwiz software 2. Locate the diagnostic connector.Insert the software CD in your CD-ROM drive. The scan tool selection menu wi

Seite 2 - READY NOT READY

CATEVAPSEC. AIRO2O HTR2EGRREADY NOT READYOBD connectorDB9 MaleMonitor Status LEDsReadyNot ReadyNot SupportedReadiness Status LEDsPC ConnectorDB9 Fema

Weitere Dokumente für Software Scantool Ready-or-Not

Um das Dokument anzuzeigen Scantool Ready-or-Not Bedienungsanleitung

Scantool Ready-or-Not Bedienungsanleitung (20 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Scantool Ready-or-Not Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Software Scantool Ready-or-Not herunter. ScanTool Ready-or-Not User Manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Software Scantool Ready-or-Not

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Scantool Ready-or-Not